Honda Civic/Acura Integra

since 1994 release

Repair and operation of the car



Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ Cooling system and heating
+ Power supply system and release
+ Electric equipment of the engine
+ Control systems of the engine
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Specifications
   Care of components of a body and bottom of the car
   Care of vinyl elements of finishing
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and locks of the car
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of assemblies of forward and back bumpers
   Removal and installation of forward wings
   Removal and installation of a latch, cylinder of the lock and emphasis of a door of a back
   Removal, installation and adjustment of a door of a back
   Removal and installation of a latch, cylinder of the lock and emphasis of a cover of a luggage compartment
   Removal, installation and adjustment of a cover of a luggage compartment
   Driving cables of an otpuskaniye of locks of covers of a luggage compartment and hatch of a jellied mouth of a fuel tank
   Removal and installation of an internal upholstery of doors
   Removal, installation and adjustment of provision of doors
   Removal and installation of latches and cylinders of locks and external and internal handles of doors
   Removal and installation of door glasses
   Removal and installation of the regulator of a window regulator
   Removal and installation of rear-view mirrors
   Removal and installation of the central console
   Removal and installation of the dashboard
   Removal and installation of a casing of a steering column
   Removal and installation of an instrument guard
   Removal and installation of a forward fairing
   Removal and installation of seats
   + Control body sizes
+ Onboard electric equipment





Removal and installation of latches and cylinders of locks and external and internal handles of doors

Assembly of a latch of the lock

 PERFORMANCE ORDER

1. Lift a windowpane and remove the panel of an internal upholstery of a door (see Removal and installation of an internal upholstery of doors).

2. Through a big opening in a doorframe disconnect the rod connecting the external handle to a latch. Do the same with a rod of the internal handle, and also with rods of external and internal locks and the electromagnetic actuation mechanism (at the corresponding complete set) (see an accompanying illustration).

3. All rods fasten by means of plastic clamps. Release the part of a clamp entering gearing with a rod, then pull a rod, releasing it from a landing opening.

4. Turn out screws of fastening of a latch to a door (see an accompanying illustration). Take assembly of a latch through the opening provided in a doorframe.

5. Installation is made upside-down.

External handle and cylinder of the door lock

 PERFORMANCE ORDER

1. Close a window and remove the panel of an internal upholstery of a door and the water filter (see Removal and installation of an internal upholstery of doors).

2. Through an opening in a doorframe release plastic clamps of fastening to a latch of executive rods external the handle and the lock of a door (see an accompanying illustration).

3. Turn out bolts of fastening of the external handle (see an illustration above).
4. Remove the handle and assembly of the cylinder of the lock from the car.
5. Installation is made upside-down.

Internal handle

 PERFORMANCE ORDER

1. Remove the panel of an internal upholstery and separate the water filter (see Removal and installation of an internal upholstery of doors).

2. Release directing an executive rod, then turn out screws of fastening of the handle (see an accompanying illustration).

3. Release the handle from a door and disconnect an executive rod from its back party. Remove the handle.
4. Installation is made upside-down.