Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
- Engine
- Repair of the engine without extraction from the car - the Civic model
General information
Preparatory actions and the list of repair procedures which can be executed without extraction of the engine from the car
Reduction of the piston of the first cylinder in the provision of the top dead point (TDP)
Removal and installation of a cover of a head of cylinders
Removal and installation of the inlet pipeline
Removal and installation of a final collector
VTEC systems - the general information and check of a condition of components
Removal, check of a state and installation of assembly of yokes
Replacement of valvate springs with plates and maslootrazhatelny caps
Removal, check of a state and installation of a gas-distributing belt and cogwheels of the GRM drive
Replacement of a forward epiploon of a cranked shaft
Removal, check of a state and installation of a camshaft
Removal and installation of a head of cylinders
Removal and installation of the pallet of a case of the engine
Removal, check of a state and installation of the oil pump
Removal and installation of a flywheel / driving disk
Replacement of a back epiploon of a cranked shaft
Check of a state and replacement of support of a suspension bracket of the power unit
+ Repair of the engine without extraction from the car - the Integra model
+ General and capital repairs of the engine
+ Cooling system and heating
+ Power supply system and release
+ Electric equipment of the engine
+ Control systems of the engine
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal and installation of a flywheel / driving disk
Removal
|
|
1. The car also establish to Poddomkratta it on props. Remove a transmission (see the Head Korobk of gear shifting).
2. On models remove coupling assembly from RKPP (see the Head Stsepleniye and power shafts). At once check a condition of components of coupling and the directing bearing.
|
|
3. Turn out bolts of fastening of a flywheel / a driving disk to a cranked shaft (see an accompanying illustration). If in the course of weakening of bolts the shaft starts being turned, remove a starter (see the Head Elektrooborudovaniye of the engine) and jam a screw-driver between teeths of a wreath of a flywheel (RKPP), or pass a long drift throughout one of openings of a driving disk, having rested it against a ledge on the block (AT). |
4. Remove a flywheel / a driving disk from a cranked shaft.
|
|
The flywheel / a driving disk is rather heavy component – it will be reasonable to resort to the help of the assistant. |
5. Carefully wipe a flywheel, having completely removed from it traces of oil and greasing. Check a working surface of a flywheel for existence of cracks, the furrows left heads of rivets of a frictional disk of coupling, traces of an overheat and zadir. Minor defects can be eliminated by means of a fine-grained emery paper. Check a gear wreath for existence of cracks and chips of teeths. Lay a flywheel on a flat surface for the purpose of an assessment of its planeness (use the planeness measuring instrument).
6. Wipe the interfaced flywheel surfaces / a driving disk and a cranked shaft. If signs of leak of oil through a back epiploon of a cranked shaft take place, make its replacement (see Replacement of a back epiploon of a cranked shaft). |
|
Installation
|
|
1. Establish a flywheel / a driving disk on a cranked shaft.
|
|
On some engines the directing pin is provided, or fixing openings are located asymmetrically that guarantees unambiguity of landing of a detail. Before rolling fixing bolts, grease from carving part with the fixing sealant. |
2. Having blocked a flywheel / a driving disk from a provorachivaniye (see paragraph 3), tighten fixing bolts with the demanded effort in a diagonal order.
3. Further installation is made as it should be, the return to a dismantle order. |
|
|
|
