Honda Civic/Acura Integra
since 1994 release
Repair and operation of the car
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine without extraction from the car - the Civic model
- Repair of the engine without extraction from the car - the Integra model
Preparatory actions and the list of repair procedures which can be executed without extraction of the engine from the car
Reduction of the piston of the first cylinder in the provision of the top dead point (TDP)
Removal and installation of a cover of a head of cylinders
Removal and installation of the inlet pipeline
Removal and installation of a final collector
Removal, check of a state and installation of a gas-distributing belt and cogwheels of the GRM drive
Replacement of a forward epiploon of a cranked shaft
VTEC systems - the general information and check of a condition of components
Removal, check of a state and installation of camshafts and assembly of yokes
Replacement of valvate springs with plates and maslootrazhatelny caps
Removal and installation of a head of cylinders
Removal and installation of the pallet of a case of the engine
Removal, check of a state and installation of the oil pump
Replacement of a flywheel / driving disk
Replacement of a back epiploon of a cranked shaft
Check of a state and replacement of support of a suspension bracket of the power unit
+ General and capital repairs of the engine
+ Cooling system and heating
+ Power supply system and release
+ Electric equipment of the engine
+ Control systems of the engine
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Onboard electric equipment
VTEC systems – the general information and check of a condition of components
Many of models of Honda cars are equipped with electronic system of correction of phases of gas distribution (VTEC).
Distinction between the ordinary engines and engines equipped with VTEC system consists in a complete set and the principle of operation of the valvate mechanism. A design of the block of the engine and all hinged knots and units, and also schemes of the organization of lubrication systems and cooling on both units are identical. The engine which is externally equipped with VTEC system differs in existence from above on a cover of a head of cylinders of a convex inscription of the corresponding contents (VTEC).
The inlet camshaft is equipped with three cams for each of the valves given by it. The special module of management of the power (RSM), proceeding from the data arriving from information sensors defines what of sets of cams into each present situation has to bring inlet valves of combustion chambers. On the basis of the analysis of the arriving information of RSM includes or switches off VTEC system.
As the initial parameters defining functioning of VTEC the following is used:
a) Frequency of rotation of the engine (rpm);
At small turns of the engine both primary, and secondary inlet valves work from own cams and open on identical height and with an identical duration, providing a good torque in the lower range of turns and the high speed of reaction to gas.
When there is a need for increase of return of the engine, yokes of primary and secondary inlet valves by means of the special hydraulic device with electronic control are blocked with an intermediate yoke. Thus duration and height of opening of both valves is defined by a form of the intermediate cam differing in the bigger height and smaller pointedness of rise.
Check of a condition of components
Electromagnetic valve of blocking / datchik-vyklyuchatel pressure
The electromagnetic valve of blocking of VTEC system including the sensor switch of pressure is located in the left part of a back wall of the engine (from a partition of a motive compartment).
Models 1994 and 1995 of vyp.
Malfunctions in a contour of the electromagnetic valve of blocking of VTEC lead to registration of a code of malfunction (DTC) 21 in memory of the control unit. On the car dashboard thus the control lamp "Lights up check the engine". Detailed information on DTC of systems of self-diagnostics it is provided in the Head of the Control system of the engine.
Failure of the sensor switch of pressure leads to the record DTC 22 and operation of a control lamp "Check the engine".
Models since 1996 vyp.
Refusal in contours of the electromagnetic valve or sensor switch of pressure leads to operation of a control lamp "Check the engine" and records in memory of the DTC P1259 control unit. Reading of diagnostic codes requires the OBD II scanner (see the Head of the Control system of the engine).
Yokes with masloraspylitel
Assemblies of proofreaders of valvate gaps