Honda Tsivik + Cars of the Honda Civic and Acura Integra brand + Maintenance instruction + Routine maintenance + Engine + Cooling system and heating + Power supply system and release + Electric equipment of the engine + Control systems of the engine + gear shifting Box + Coupling and power shafts + Brake system - Suspension bracket and steering Specifications Removal and installation of assembly of the forward shock-absorber with a screw spring Replacement of the shock-absorber or screw spring of rack-mount assembly of a forward suspension bracket Removal and installation of the forward stabilizer of cross stability with basic plugs Removal and installation of the top control lever of a forward suspension bracket Removal and installation of the lower control lever of a forward suspension bracket Removal and installation of a rotary fist and stupichny assembly Removal and installation of assembly of a forward nave with the wheel bearing Replacement of spherical support Removal and installation of assembly of the back shock-absorber with a screw spring Removal and installation of a bar of the back stabilizer of cross stability with basic plugs Removal and installation of assembly of a back nave with the wheel bearing Removal and installation of levers of a back suspension bracket Removal and installation of a steering wheel Removal and installation of tips of steering drafts Replacement of protective covers of the steering mechanism Removal and installation of the steering mechanism Removal and installation of the steering pump Removal of air from a hydraulic path of system of strengthening of a wheel Wheels and tires - the general information Corners of installation of wheels + Body + Onboard electric equipment
|
Removal and installation of levers of a back suspension bracket
|
1. Weaken nuts of fastening of the corresponding wheel. A car back also establish to Poddomkratta it on props. Remove a wheel. |
|
Top lever
|
|
1. Give a nut of a through bolt of fastening of the top lever of a suspension bracket to the longitudinal lever (see an accompanying illustration), take a bolt. |
2. Turn out bolts of a collar of fastening of the basic plug of the internal end of the lever to the car bottom (see an illustration above). Remove the top lever. 3. Check the basic plug for existence of cracks, signs of hardening or aging of rubber. The defective plug is subject to a vypressovyvaniye and replacement – work should be performed in the conditions of a workshop of car service. 4. Installation is made upside-down. Track observance of the demanded efforts of a tightening of fixture. |
|
Lower lever
|
1. Turn out a bolt of fastening of the lower lever to longitudinal, and also a bolt of fastening of damping assembly to the lower lever (see Removal and installation of assembly of the back shock-absorber with a screw spring).
|
2. Give a nut and take an axial bolt of fastening of the internal end of the lower lever to the car chassis (see an accompanying illustration). Remove the lower lever. |
3. Check a condition of basic plugs, in case of need make their replacement in the conditions of a workshop of car service (the press will be required). 4. Installation is made upside-down. Track observance of the demanded efforts of a tightening of fixture. |
|
Compensation lever
|
|
1. Turn out a bolt of fastening of the compensation lever to longitudinal (see an accompanying illustration). |
2. Give a nut of a through bolt of fastening of the compensation lever to the car bottom (see an illustration above). Take a bolt and remove the compensation lever. 3. Check a condition of basic plugs, in case of need make their replacement in the conditions of a workshop of car service (the press will be required). 4. Installation is made upside-down. Track observance of the demanded efforts of a tightening of fixture. |
|
Longitudinal lever
|
1. Disconnect a hydraulic hose from the wheel cylinder / a back support. At once to a zakuporta the open ends of a hose and the union in order to avoid hit in system of dirt. Remove the brake drum and shoe assembly. On models with disk brake mechanisms of back wheels remove a support and a brake disk. Disconnect a cable of the drive of the parking brake from the executive lever (see the Head Brake system). 2. Remove a board of the brake mechanism. 3. Disconnect from the longitudinal lever of assembly of the top, lower and compensation levers (see above).
|
4a. Release a cable of the drive of the parking brake from an arm on assembly of the longitudinal lever. Turn out bolts of fastening of an axis of the basic plug of the longitudinal lever to the bottom of the car and remove the lever (see accompanying illustrations): left bolt of fastening. |
|
4b. Right bolt of fastening. |
5. Check a condition of basic plugs, in case of need make their replacement in the conditions of a workshop of car service (the press will be required). 6. Installation is made upside-down. Track observance of the demanded efforts of a tightening of fixture. |
|
|
|